The EtherChannel between your LAN switch and the Internet router is not load-balancing efficiently. On the switch，there are several workstations with valid IP ranges. Which load-balance algorithms can you use in the switch in order to optimize this load b

题目

The EtherChannel between your LAN switch and the Internet router is not load-balancing efficiently. On the switch，there are several workstations with valid IP ranges. Which load-balance algorithms can you use in the switch in order to optimize this load balancing？ （）

  • A、source IP address
  • B、destination IP address
  • C、per-packet load balance
  • D、destination MAC address
  • E、source MAC address
相似考题

1.You need to perform. some initial configuration tasks on a new Ezonexam switch. What is the purpose of assigning an IP address to a switch?A．To provide local hosts with a default gateway addressB．To allow remote management of the switch.C．To allow the switch to respond to ARP requests between two hostsD．To ensure that hosts on the same LAN can communicate with each other.E．None of the above

2.An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）A. Router routes traffic between different networks and a switch does notB. The new switch is faulty and needs to be replaced and configured correctlyC. The firewall needs to be setup to allow traffic to reach the InternetD. The switch needs to be setup to forward data traffic to the Internet

3.You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A. The switch name must match the workgroup name of the local network.B. The switch must be configured with an IP address and default gateway.C. The remote workstations must have access to the management VLAN of the switch.D. CDP must be enabled on the switch so that it can be located by other devices on the network.

4.How can you reset your router or switch to factory defaults?()A.reset configurationB.load factory-defaultC.load override defaultD.set default configuration

更多“The EtherChannel between your LAN switch and the Internet router is not load-balancing efficiently. On the switch，there are several workstations with valid IP ranges. Which load-balance algorithms can you use in the switch in order to optimize this load b”相关问题

  • 第1题：

    In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?()

    A. Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.

    B. A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.

    C. A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.

    D. A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.


    参考答案：B

  • 第2题：

    You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?()

    A. Switch(config)# ip default-network 192.168.12.1

    B. Switch(config)#ip route-default 192.168.12.1

    C. Switch(config)# ip default-gateway 192.168.12.1

    D. Swicth(config)# ip route 192.168.12.1 0.0.0.0


    参考答案：C

  • 第3题：

    Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs()。

    A.a switch with a trunk link that is configured between the switches

    B.a router with an IP address on the physical interface that is connected to the switch

    C.a switch with an access link that is configured between the switches

    D.a router with subinterfaces configured on the physical interface that is connected to the switch


    参考答案：D

  • 第4题：

    You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?（）

    • A、Switch(config)# ip default-network 192.168.12.1
    • B、Switch(config)#ip route-default 192.168.12.1
    • C、Switch(config)# ip default-gateway 192.168.12.1
    • D、Swicth(config)# ip route 192.168.12.1 0.0.0.0

    正确答案:C

  • 第5题：

    You have just created a new VLAN on your network.  What is one step that  you should include in your VLAN based implementation and verification plan？ （）

    • A、Verify that different native VLANs exist between two switches for security purposes.
    • B、Verify that the VLAN was added on all switches with the use of the show vlan command. 
    • C、Verify that the switch is configured to allow for trunking on the switch ports.
    • D、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.

    正确答案:B

  • 第6题：

    An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）

    • A、The switch must be configured with an IP address, subnet mask, and default gateway.
    • B、The switch must be connected to a router over a VLAN trunk.
    • C、The switch must be reachable through a port connected to its management VLAN.
    • D、The switch console port must be connected to the Ethernet LAN.
    • E、The switch management VLAN must be created and have a membership of at least one switch

    正确答案:A,C

  • 第7题：

    On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）

    • A、a router with subinterfaces configured on the physical interface that is connected to the switch
    • B、a router with an IP address on the physical interface connected to the switch
    • C、a switch with an access link that is configured between the switches
    • D、a switch with a trunk link that is configured between the switches

    正确答案:A

  • 第8题：

    An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）

    • A、Router routes traffic between different networks and a switch does not
    • B、The new switch is faulty and needs to be replaced and configured correctly
    • C、The firewall needs to be setup to allow traffic to reach the Internet
    • D、The switch needs to be setup to forward data traffic to the Internet

    正确答案:A

  • 第9题：

    单选题
    In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）
    A

    Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.

    B

    A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.

    C

    A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.

    D

    A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.


    正确答案： A
    解析： 暂无解析

  • 第10题：

    单选题
    You have just created a new VLAN on your network.  What is one step that  you should include in your VLAN based implementation and verification plan？ （）
    A

    Verify that different native VLANs exist between two switches for security purposes.

    B

    Verify that the VLAN was added on all switches with the use of the show vlan command. 

    C

    Verify that the switch is configured to allow for trunking on the switch ports.

    D

    Verify that each switch port has the correct IP address space assigned to it for the new VLAN.


    正确答案： A
    解析： 暂无解析

  • 第11题：

    多选题
    An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）
    A

    The switch must be configured with an IP address,subnet mask,and default gateway.

    B

    The switch must be connected to a router over a VLAN trunk.

    C

    The switch must be reachable through a port connected to its management VLAN.

    D

    The switch console port must be connected to the Ethernet LAN.

    E

    The switch management VLAN must be created and have a membership of at least one switch port.

    F

    The switch must be fully configured as an SNMP agent.


    正确答案： B,D
    解析： 暂无解析

  • 第12题：

    多选题
    The LAN needs are expanding at the Testking corporate office, which is quickly growing. You are instructed to enlarge the area covered by a single LAN segment on the TestKing network.Which of the following are layer 1 devices that you can use?（）
    A

    A switch.

    B

    A router.

    C

    A network adapter card.

    D

    A hub.

    E

    A repeater.


    正确答案： B,E
    解析： 暂无解析

  • 第13题：

    The LAN needs are expanding at the Testking corporate office, which is quickly growing. You are instructed to enlarge the area covered by a single LAN segment on the TestKing network.Which of the following are layer 1 devices that you can use?（）

    A. A switch.

    B. A router.

    C. A network adapter card.

    D. A hub.

    E. A repeater.


    参考答案：D, E

  • 第14题：

    On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）

    A.a router with subinterfaces configured on the physical interface that is connected to the switch

    B.a router with an IP address on the physical interface connected to the switch

    C.a switch with an access link that is configured between the switches

    D.a switch with a trunk link that is configured between the switches


    参考答案：A

  • 第15题：

    The LAN needs are expanding at the Testking corporate office, which is quickly growing. You are instructed to enlarge the area covered by a single LAN segment on the TestKing network.Which of the following are layer 1 devices that you can use?（）

    • A、A switch.
    • B、A router.
    • C、A network adapter card.
    • D、A hub.
    • E、A repeater.

    正确答案:D,E

  • 第16题：

    Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。

    • A、a switch with a trunk link that is configured between the switches
    • B、a router with an IP address on the physical interface that is connected to the switch
    • C、a switch with an access link that is configured between the switches
    • D、a router with subinterfaces configured on the physical interface that is connected to the switch

    正确答案:D

  • 第17题：

    An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）

    • A、The switch must be configured with an IP address,subnet mask,and default gateway.
    • B、The switch must be connected to a router over a VLAN trunk.
    • C、The switch must be reachable through a port connected to its management VLAN.
    • D、The switch console port must be connected to the Ethernet LAN.
    • E、The switch management VLAN must be created and have a membership of at least one switch port.
    • F、The switch must be fully configured as an SNMP agent.

    正确答案:A,C

  • 第18题：

    What is the purpose of assigning an IP address to a switch?（）

    • A、Provides local hosts with a default gateway address
    • B、Allows remote management of the switch.
    • C、Allows the switch to respond to ARP requests between two hosts
    • D、Ensures that hosts on the same LAN can communicate with each other.

    正确答案:B

  • 第19题：

    You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）

    • A、The switch name must match the workgroup name of the local network.
    • B、The switch must be configured with an IP address and default gateway.
    • C、The remote workstations must have access to the management VLAN of the switch.
    • D、CDP must be enabled on the switch so that it can be located by other devices on the network.

    正确答案:B,C

  • 第20题：

    How can you reset your router or switch to factory defaults?（）

    • A、reset configuration
    • B、load factory-default
    • C、load override default
    • D、set default configuration

    正确答案:B

  • 第21题：

    多选题
    You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）
    A

    The switch name must match the workgroup name of the local network.

    B

    The switch must be configured with an IP address and default gateway.

    C

    The remote workstations must have access to the management VLAN of the switch.

    D

    CDP must be enabled on the switch so that it can be located by other devices on the network.


    正确答案： D,B
    解析： 暂无解析

  • 第22题：

    多选题
    An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
    A

    The switch must be configured with an IP address, subnet mask, and default gateway.

    B

    The switch must be connected to a router over a VLAN trunk.

    C

    The switch must be reachable through a port connected to its management VLAN.

    D

    The switch console port must be connected to the Ethernet LAN.

    E

    The switch management VLAN must be created and have a membership of at least one switch


    正确答案： A,B
    解析： 暂无解析

  • 第23题：

    单选题
    An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）
    A

    Router routes traffic between different networks and a switch does not

    B

    The new switch is faulty and needs to be replaced and configured correctly

    C

    The firewall needs to be setup to allow traffic to reach the Internet

    D

    The switch needs to be setup to forward data traffic to the Internet


    正确答案： B
    解析： 暂无解析

相关内容