What must be configured on the Cisco Unity Express host router prior to installation of the CUE module?（）A、Set up the Network Time Protocol server. B、Install the files needed to run the web-based GUI. C、Set up routing and IP addressing on the service modu

第1题：

You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have  assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state.  What must be true in an SVI configuration to bring the VLAN and line protocol up？（）

• A、The port must be physically connected to another Layer 3 device.
• B、At least one port in VLAN 20 must be active.
• C、The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
• D、Because this is a virtual interface， the operational status will always be in an "up/up" state.

第2题：

Acme Booster Corporation has a corporate policy stating that all routing devices will have their configurations backed up to a corporate server on a weekly basis. Their CUE module is a component of the Cisco CallManager Express device. Which three parameters will ensure successful backup of the CUE module configuration?（）

• A、ATFTP server must be present and available to the CUE module. 
• B、The CUE module must have modify permissions on the backup server directory. 
• C、The CUE module must be in an offline mode prior to instituting the backup. 
• D、An FTP server must be present and available to the CUE module. 
• E、The CUE module must copy the configuration and messages to separate directories on the backup server. 
• F、The CUE module must have read and write permissions on the backup server directory.

第3题：

You develop a service application that needs to be deployed. Your network administrator creates a specific user account for your service application.You need to configure your service application to run in the context of this specific user account. What should you do？（）

• A、Prior to installation，set the StartType property of the ServiceInstaller class.
• B、Prior to installation，set the Account，Username，and Password properties of theServiceProcessInstaller class.
• C、Use the CONFIG option of the net.exe command-line tool to install the service.
• D、Use the installutil.exe command-line tool to install the service.

第4题：

You install a wireless router and disable the Service Set Identifier （SSID） broadcast feature. You need to configure your computer to connect to the wireless network.  What should you do？ （）

• A、Click the Connect to a network link， right-click the appropriate network， and then click the Connect option.
• B、Click the View computers and devices link， right-click the wireless router， and then click the Enable option.
• C、Click the Set up a connection or network link， and then click the Set up a wireless Ad hoc network option.
• D、Click the Set up a connection or network link， and then click the Manually connect to a wireless network option.

第5题：

Which of the following would be the BEST safety measure to take before installing a Windows service pack？（）

• A、Back up all important documents. 
• B、Set a System Restore point. 
• C、Note the BIOS settings in case a reset is needed. 
• D、Back up the drivers for the computer in case re-installation is needed. 
• E、Uninstall the previous service pack.

第6题：

Mike has been using RIS (Remote Installation Services), to install all new workstations on his network. A new Service Pack has recently been released from Microsoft and he wants to update his new image. He brings up his test workstation that has Windows 2000 Professional on it and installs the new Service Pack.  What is the next step Mike must take?（）

• A、Slipstream this Service Pack to the CD image on the RIS Server.
• B、Use xcopy to copy all files to the RIS server.
• C、Run Riprep.exe
• D、Run Sysprep.exe

第7题：

Most of the Windows 2000 Professional clients on your network use the TCP/IP Protocol to communicate with Server. You want to increase network performance. Where do you change the binding order of your protocols？ （）

• A、On the Windows 2000 Server， set TCP/IP for the Server service at the top.
• B、On the Windows 2000 Professional computers， set TCP/IP for the Workstation service at the top.
• C、On the Windows 2000 Server， set TCP/IP for the Workstation service at the top.
• D、On the Windows 2000 Professional computers， set TCP/IP for the Server service at the top.

第8题：

Your network uses ipv4. You install a server that runs windows server 008 at a brach office. The server is configured with two network interfaces. You need to configure routing on the server at the branch office. Which two actions should you perform? （）

• A、Install the routing and remote access role.
• B、Run the netsh ras ip set access ALL command.
• C、Run the netsh interface ipv4 enable command.
• D、Enable the IPV4 router routing and remote access option.

第9题：

第10题：

第11题：

第12题：

第13题：

An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF？（）

• A、Ensure that an interface has been configured with an IP address
• B、Ensure that IP classless is enabled
• C、Ensure that the interfaces can ping their directly connected neighbors
• D、Ensure that an interface has been configured with an IP address and is up

第14题：

What is the maximum number of network locales that can be configured for any one Cisco Unified CallManager Express when using the cnf-file perphone command?（）

• A、1 
• B、2 
• C、4 
• D、5
• E、a number equal to the number of languages supported by Cisco Unity Express 
• F、a number equal to the number of languages supported by Cisco Unity CallManager Express

第15题：

You set up scheduled tasks to run and notify you of any failures. 3 days later you see that none of the tasks ran and you received no notifications. What should you do？（）

• A、Set the schedule service to run under the administrator account.
• B、Set the scheduled tasks to run under the administrator account.
• C、Enable the messenger service
• D、Set the schedule service to run under the local system account and set it to start automatically.

第16题：

When setting an access point to a non-root role， what two parameters，other than Role in theRadio Network，must be configured on the SSID Manager page？（）

• A、Infrastructure devices to associate only to this SSID
• B、Enable IP redirection on this SSID
• C、Set Data Beacon Rate
• D、Multiple Basic Service Set Identification （BSSID）
• E、Set infrastructure SSID

第17题：

Your network uses IPv4. You install a server that runs Windows Server 008 at a brach office. The server is configured with two network interfaces. You need to configure routing on the server at the branch office. Which two actions should you perform？（） 

• A、 Install the Routing and Remote Access role.
• B、 Run the netsh ras ip set access ALL command
• C、 Run the netsh interface ipv4 enable command
• D、 Enable the IPv4 Router Routing and Remote Access option

第18题：

Your network uses IPv4.You install a server that runs Windows Server 2008 R2 at a branch office. The server is configured with two network interfaces. You need to configure routing on the server at the branch office.Which two actions should you perform？（）

• A、Install the Routing and Remote Access Services role service.
• B、Run the netsh ras ip set access ALL command.
• C、Run the netsh interface ipv4 enable command.
• D、Enable the IPv4 Router Routing and Remote Access option.

第19题：

You work as the enterprise exchange administrator at Xxx .The Xxx network consists of a domain named xxx .What actions must you take to use administrative delegation on a series of cmdlets？（）

• A、You must implement log transactions
• B、You must set up new management role
• C、You must implement Mailbox journaling
• D、You must set up a Role Based Access Control （RBAC） role

第20题：

Your network uses IPv4.You install a server that runs Windows Server 2008 at a branch office.The server is configured with two network interfaces. You need to configure routing on the server at the branch office.Which two actions should you perform？ （Each correct answer presents part of the solution.（）

• A、Install the Routing and Remote Access Services role service.
• B、Run the netsh ras ip set access ALL command.
• C、Run the netsh interface ipv4 enable command.
• D、Enable the IPv4 Router Routing and Remote Access option.

第21题：

第22题：

第23题：